Need Help?

Need help with an existing system?

View Manuals

Frozen Condensate Guidance for Households

Share this article:

During recent winters the UK has experienced prolonged spells of extremely cold weather - down to minus 20oC and below in many areas.

The Following 3 maps show the extend of the dramatic fall in temperatures:

Winter 2007 Winter 2009Winter 2010






This resulted in a significant increase in the number of calls to boiler manufacturers and heating engineers from householders with condensing (high efficiency) boilers where the condensate drainage pipe had frozen and become blocked with ice, causing the boiler to shut down. In the vast majority of cases such problems occur where the condensate drainage pipe is located externally to the building for some part of its length.

British Standards, Building Regulations and boiler manufacturers’ installation instructions currently allow condensate drainage pipes to be located either internally or externally, or a combination of these. These documents give guidance on how to install the condensate drainage pipes in order to reduce the possibility of freezing. However this guidance may not be sufficient to prevent freezing in extreme conditions of the type recently experienced in the UK - with widespread and prolonged very low temperatures.  

This note gives guidance for householders on what to do if a boiler condensate drainage pipe has frozen - provided they feel competent to take the actions described.

If you do not feel competent to follow this guidance then you should contact your regular servicing organisation or a local Gas Safe registered engineer, explain the situation and arrange for them to resolve the problem. They will also be able to advise on ways to reduce the likelihood of freezing in future. Registered gas engineers in your area can be found using the postcode search facility on the Gas Safe Register website at

If you have access to the internet, additional guidance may be available on the websites of boiler manufacturers or larger service companies.

There are a number of measures, detailed below, which householders may wish to take in order to thaw the condensate drainage pipe, free the blockage and re-start the boiler themselves  provided they feel competent to do so  -

1. Confirm that a frozen condensate drain pipe is the cause of shutdown.

It is important to confirm that a frozen condensate drainage pipe is the likely cause of the problem before taking any of the remedial actions suggested below.
The condensate drainage pipe is a plastic pipe (typically grey or white in colour) coming from the bottom of your boiler. 

If the following circumstances apply then it is probable that a frozen condensate drainage pipe is the cause -

  • outside temperatures have been below freezing for some time.
  • the condensate drainage pipe runs through the wall and outside the property for part of its length, without any increased pipe diameter, insulation or other measures to prevent freezing. There may also be a problem if the pipe runs through an enclosed but unheated area, such as a garage or loft.
  • the boiler has previously been working satisfactorily.

Shutdown due to freezing and blockage of the condensate drainage pipe will usually be indicated by a “fault code” on the boiler’s digital display, although this may not specifically indicate freezing as the fault. Indication may also be given by some other alarm such as a flashing light, or by a symptom such as “gurgling” noises coming from the boiler. 

Note - refer to the boiler manual for guidance on fault codes/alarms and their meaning - the boiler manufacturer or the servicing company you use may also have a helpline or website giving guidance on this.

2. Locate the blockage.

It is likely that the pipe is frozen at the most exposed point external to the building or where there is some obstruction to flow. This could be at the open end of the pipe, at a bend or elbow, or where is a dip in the pipe in which condensate can collect. The location of the blockage should be identified as closely as possible before taking further action.

3. Thaw the frozen pipe.

Note: You should not attempt to thaw a condensate drain pipe if you cannot easily reach it from ground level. Be aware that any water used can quickly freeze if it falls onto pathways - causing a possible slip hazard.

The pipe can be thawed by applying a hot water bottle, a microwaveable heating pack (the sort used for muscular aches and pains) or cloths soaked in warm water to the exterior of the pipe, close to the likely point of blockage. Warm water can also be poured onto the pipe from a watering can or similar container. Do not use boiling water.

4. Reset/re-start the boiler.

Once the blockage has been thawed and cleared, consult the boiler operating instructions or check the manufacturer’s website for guidance on any action needed to “reset” the fault code/alarm and start the boiler. 

In most cases, once the condensate drain pipe is cleared and a reset has been carried out, the boiler will re-ignite using an automatic operating sequence.

If this reset/restart does not succeed you should call in a competent engineer to assess the situation and take further action if required.

5. Temporary remedial actions:

If the pipe is successfully thawed and the boiler can be re-started then the following temporary remedial actions may help prevent re-freezing if the severe weather continues.

  1. If the external pipe is not insulated as recommended, you should try to rectify this by attaching suitable water-proof and weather-proof insulation over the outside of the pipe to prevent re-freezing. “Class O” pipe insulation is suitable for external use and should be available from DIY outlets and plumbing/heating suppliers.
  2. During the cold spell it may help to temporarily run the heating system with the boiler thermostat (as distinct from the room thermostat) set to maximum. Turn back to the normal setting used once the cold spell is over.
  3. It may also help to temporarily set the central heating timer/programmer to “continuous” (24hr) mode, setting the room thermostat overnight to around 15oC. Again, return to the normal settings once the cold spell is over.

6. Longer term actions:

As previously stated, British Standards, Building Regulations etc. currently allow condensate drainage pipes to run either internally or externally (or a combination of these). These documents give recommendations on how to run the pipe and use insulation, if required,  in order to reduce the possibility of freezing, This guidance was based on the UK winter conditions prevailing until very recently, however it may not have been sufficient to prevent freezing in extreme conditions. 

Should you wish to take action in order to reduce the risk of freezing in future, by relocating the condensate drainage pipe or taking other measures, then more detailed guidance is available from your installer or service engineer, or on-line here

7. FAQs

What is condensate and what does the condensate drain do? 

High efficiency (condensing) boilers remove more useful heat from the combustion gases, resulting in additional water vapour which has to be collected within the boiler, as condensate, and taken to a suitable drainage point via the condensate drainage pipe.

Why has my condensate drain only frozen recently?

Recently the UK has suffered from unusually cold weather, over unusually prolonged periods. Existing recommendations for condensate pipe installation, such as pipe insulation, were based on prevailing UK weather conditions and may not be sufficient in the extreme conditions recently experienced across much of the UK.

Shouldn’t my condensate drainage pipe have been installed correctly in the first place?

British Standards, Building Regulations etc. currently allow condensate drainage pipes to be run internally, externally or a combination of these. These documents give recommendations on how to run the pipe and use insulation in order to reduce the possibility of freezing, This guidance was based on the UK winter conditions prevailing until very recently, however it may not have been sufficient to prevent freezing in extreme weather conditions. 

Can I improve the pipe installation to prevent freezing

It would be advisable to examine the condensate drainage pipework and upgrade the installation if required, to reduce the risk of freezing in future. This should be done by a competent person in accordance with relevant British Standards and industry guidance (see below).

HHIC has published updated industry guidance on condensate drainage pipe installation, which should be followed if this work is carried out. Click here for details.

A heating engineer cut the condensate pipe to get my boiler working and left the pipe discharging to a bucket as an “emergency measure”. Is this acceptable?

It is recognised that in some instances (e.g. where an elderly person’s heating needs to be reinstated as an emergency measure) frozen condensate drainage pipes may have been cut in order to bypass the blockage. This has been done to allow re-ignition of the boiler, with condensate being collected in a suitable container as a temporary solution. 

While not unsafe, this is not recommended practice and if such action has been taken then the condensate drainage pipe must be reinstated as soon as possible, using the appropriate industry guidance (see above) to reduce risk of freezing in future.

Download as a PDF

  • Manuals

    Access our comprehensive library of manuals for a wide selection of manufacturers for boilers, heat pumps, solar thermals and gas fires.

    View all manuals
  • Find an Installer

    Search our national database of Benchmark-registered heating installers.

    Find an installer
  • Heating Advice

    Our Heating Advice section is a library of questions we have been asked and our responses. Visit our Heating Advice section to see if we can help with your query.

    View heating advice

Latest from HHIC:

RT @energyutilities: With #carbonbudgets, increasing #fuelpoverty & concerns re the sustainability of the UK’s energy, it's worrying that t…

Follow us